Hermes RB 346 J-Flex Abrasive Roll 76mm x 25m
Hermes RB 346 J-Flex Abrasive Roll 76mm x 25m
£84.50 (£70.42 Ex. VAT)

Hermes RB 346 J-Flex Abrasive Roll 76mm x 25m

  • 76mm wide Hermes RB 346 J Flex cloth backed abrasive
  • For many single drum sanders and belt linishers
  • Highly flexible aluminium oxide abrasive
  • Long lasting and highly durable
£84.50 (£70.42 Ex. VAT)

Collect in store, we'll confirm your reservation within 1 hour.

Check stock at your local store

Chosen store -

Loading stock for

In stock - collect from in 1 hour

Low stock - collect from in 1 hour

Out of stock at

Change store
Learn how it works

We're commited to selling high-quality products, however we also know thats there are times when you need to exchange or return an item.

  • No quibble 30 day returns policy
  • Arrange your return online, in-store or by phone
  • Simple and easy returns process
Find out more

In Detail

Hermes RB 346 J Flex highly flexible aluminium oxide abrasive for many single drum sanders or belt linishers. 76mm wide. Long lasting and highly durable. The high strength bonding system prevents premature abrasive grain shedding, giving improved abrasive life and high stock removal rates. Suitable for most metals as well as giving a good performance on wood.

N.B. Please ensure that your dust extraction system is adequate and efficient, dust remaining on the abrasive will shorten it's life and reduce it's performance.

This product is on page 52 of the Axminster Tools & Machinery 2018/19 Catalogue.


Abrasive Backing Cloth
Abrasive Material Aluminium Oxide
Abrasive Roll Length 25 m
Abrasive Roll Width 76 mm
Abrasive Type RB 346 J FLEX
Reviews (6)

Customer Reviews

Overall rating 3.4 out of 5 based on 6 reviews

Newest Customer Reviews


Phylip Henry Rees

19 September 2014

OK but could be better

The sandpaper is OK and once you come to terms with the limitation of the Jet sander, you should have a reasonable life out of the sandpaper. Just remember it is for finishing and I only use it for the first phase in that process. However, now and again, I still have the occasional new strip of sandpaper break having had little use as the paper in not very strong, and when it breaks it is rather annoying and expensive. To reduce the risk of this happening, I now strengthen the cut end of the sandpaper by gluing about 9" of old cloth onto the back of the paper and it immensely increases the life of the paper.

Niall Hammond

6 August 2014

Great - does the job and very economical

This is just the right width for the Jet 22-44 and it has to date been more than strong enough so I don't understand the reviews that say otherwise. Does the job and last for a reasonable time. I actually prefer that it is a little thinner and more flexible that the original loadings provided with sander as this makes it easier to wrap tightly.

Geoffrey Laycock

12 December 2013

Absolutely Fine

This is the same width as my original abrasive loading for my Jet 16-32 so don't understand the last review. In any case I have used a different width and it is easy to fit IF you follow the guidance and demonstration on the CD. Whatever the width of abrasive you can cut the first end using the measurements given and then following the instructions cut the second end, easy and no awkward cuts causing failure. I suspect the various negative comments may be due to not following the instructions correctly. These drum sanders are finish sanders, not a thicknesser, and using to significantly reduce thickness of timber will cause problems with abrasive. The other important thing for helping your abrasive is serious extraction. Failing to remove sanding dust will load up the abrasive in seconds, cause overheating of the abrasive and increased wear and failure.

It is expensive.


5 December 2013


Not what it says on the tin.......not the same width as the original causing a non practical cut to locate into the clips......only solution is to cut the belt down by 7.5 mm which will increase the amount of wraps around the drum but will give an accurate cut to engage the clips ....


28 October 2013

Not strong enough

I bought it for my drum sander in 120 and 240 grit. It only last for few minutes...Cloth backing is very tin and weak compare to one supplied with machine. Good for manual sanding though.

Privacy Policy & Cookies

We use cookies to improve and personalise our services, for marketing and for social activity. Please see our privacy policy for more information on how and why we use your data. You can change your cookie settings at any time. By continuing, you agree to our use of cookies.