Adjustable Vice Jaw Benders
Adjustable Vice Jaw Benders
£41.80 - £54.95 (£34.83 - £45.79 Ex. VAT)

Adjustable Vice Jaw Benders

  • Handy sheet metal benders
  • Fit to vice jaws with magnets
  • Allows a range of complex bends to be formed
  • Available in two sizes, 100mm or 150mm
£41.80 - £54.95 (£34.83 - £45.79 Ex. VAT)

Collect in store, we'll confirm your reservation within 1 hour.

Check stock at your local store

Chosen store -

Loading stock for

In stock - collect from in 1 hour

Low stock - collect from in 1 hour

Out of stock at

Change store
Learn how it works

We're commited to selling high-quality products, however we also know thats there are times when you need to exchange or return an item.

  • No quibble 30 day returns policy
  • Arrange your return online, in-store or by phone
  • Simple and easy returns process
Find out more

In Detail

Exceptionally useful sheet metal benders which fit to the jaws of a vice with magnets. The die is in three parts allowing a range of complex bends to be formed. Available in two sizes, 100mm or 150mm.



Max Material Thickness 2 mm
Overall L x W x H 100 mm = 102 mm x 87 mm x 33 mm 150 mm = 152 mm x 102 mm x 42 mm
Reviews (3)

Customer Reviews

Overall rating 5 out of 5 based on 3 reviews

Newest Customer Reviews



25 October 2017

Does what it says on the box

I needed to bend some 1/8" strip and this does the job well. For bright drawn mild steel 1" wide, it took rather an effort to start bending it and the strip cracked after bending it about 30 degrees. I then annealed the strip and it bent perfectly. I would think that bending 4" wide un-annealed BMS would be very difficult if not impossible. If you need to bend hard material, then softening it first would be a good idea. Does the job well and makes really sharp bends. It would be nice if it were supplied painted.

Peter Hoare

7 January 2013

Very useful.

Very good little tool, the magnets hold it to the vice jaws properly, and the bends are very tight, and accurate. If your bending very thin stuff though, its possible to go too far and end up with an acute angle, but thats not an issue.

One thing though as the previous reviewer said, you do need a big vice for these. Im using a large (50kg) machine vice which has ground and scraped ways, and ground jaws, which is perfect for this. You would struggle with a cheap pillar drill vice, anything where the jaws of the vice can wobble about. You also need to remember that the depth of the vice jaws is very important, as all the material on the lower side of the bend need to hang down in between the jaws, so if its a very shallow vice you wont get much material down.

That said, its doing some very nice bending in 2mm aluminium and would bend thicker with no problem. The removable blades are a nice touch too.

Derek Saxty

9 September 2010

A Brilliant Piece Of Kit.

I needed to put a 90 degree bend in a piece of mild steel about 3mm thick. Clamping it in the vice and thumping it with a hammer wasn’t going to do the job satisfactorily, but by using one of these I soon produced a well formed right angle just where I wanted it and without too much effort.

Being a slightly built pensioner I don’t think I could bend anything much thicker than 3mm, but with a bit more weight and a few less years 4mm would be possible.

You do need a good vice though, the bigger the better. The metal has to stand upright in it so you are limited by the vice’s size and the fact that the bend will be formed about 12mm below the top of the vice jaws.

A word of warning: these clamp on with VERY strong magnets, especially the V-block so take care when attaching them.

Overall, a well built tool that exceeded my expectations and looks as though it will last for many years to come.

Privacy Policy & Cookies

We use cookies to improve and personalise our services, for marketing and for social activity. Please see our privacy policy for more information on how and why we use your data. You can change your cookie settings at any time. By continuing, you agree to our use of cookies.