Axminster Bevelled Straight Edges
Axminster Bevelled Straight Edges
£39.02 (£32.52 Ex. VAT)

Axminster Bevelled Straight Edges

  • Fully ground steel
  • 38mm wide, 5mm thick
£39.02 (£32.52 Ex. VAT)

Collect in store, we'll confirm your reservation within 1 hour.

Check stock at your local store

Chosen store -

Loading stock for

In stock - collect from in 1 hour

Low stock - collect from in 1 hour

Out of stock at

Change store
Learn how it works

We're commited to selling high-quality products, however we also know thats there are times when you need to exchange or return an item.

  • No quibble 30 day returns policy
  • Arrange your return online, in-store or by phone
  • Simple and easy returns process
Find out more

In Detail

These are top quality steel workshop straight edges, 38mm wide and 5mm thick, ground on all surfaces. Their main uses are for cutting thin material such as card and veneer and for checking the straightness of lengths of timber, machine tables, plane soles and so on.

Reviews (8)

Customer Reviews

Overall rating 3.7 out of 5 based on 8 reviews

Newest Customer Reviews


Chris L

24 September 2017

5 years & still straight

Bought this about 5 years ago, (750mm). I still have the case and it was straight when I bought it and is still straight today, sharp edge is in good condition and I take care when using it. I'm not sure what more I can say other than that I'm thoroughly pleased with it.

Tom T

3 February 2017

Don't waste your money

Bought this a while ago. I thought id review it as I just wanted to say to anyone considering this tool-dont waste your money. The one I was sent isnt straight and is ground inaccurately so that the bevel edge is sharp in places, not flat at the edge like it should be. I judged its straightness against high quality Maun and Veritas edges.

Dave Edwards

17 November 2016

Good straight edge but not perfect

There have been a number of reviews stating various issues with this straight edge but my experience with this purchase is that the one I got was ok when checked against a know good straight edge with no gaps either on the wide edge or the bevel edge. This not to say there are not issues but they are relatively minor and do not prevent this tool doing its job.
For me the bevel is too sharp and could be easily damaged, as this is a precision tool anyway you need to treat as such.
Its far too shiny, what I initially thought were gaps along the edge of the bevel turned out to be reflections of the workshop lights.
The ends of the bevel are unfinished and very rough, these could have been easily tidied up without affecting the cost.

A MacInnes

29 November 2014

Not immediately useful

Despite what other reviewers have said, I went ahead and ordered the short one. Predictably it was not straight. It was bowed and daylight was shining brightly under the middle section. However, because the bevelled edge is so fine it took about 15 minutes with a diamond sharpening plate to produce dead straight. I would have done the same to a straight edge costing 5 times as much, so for me it is great. You can use a file stroked carefully along the length too, but it will take longer with more iterations. I think that people who buy straight edges probably have files so if you are prepared to do a bit of work, and have a decent reference surface, I'd recommend these.

Geoffrey Laycock

3 October 2013

The un-straight straightedge

Delivered in a cardboard tube alone and in its faux leather case, something looked wrong immediately. The overall surface ground finish looked 'whiteIsh' in parts and would not come off with degreaser.

Looking carefully it was also obvious the beveled edge was not straight, confirmed very easily with a Veritas straightedge. About 40 mm plus at one end had been over ground causing it to curve slightly, the bevel edge also thinned almost to a knife edge.

For the money, not bad but I need a good straight ! edge for accurate cutting so on its way back to Axminster via their ever helpful Customer Services.
Need Help?