Large cut capacity with high precision, constant electronics and extreme power make this 254mm saw a winner. Fitted with an integrated sliding table, expanding table top and integrated rear outfeed for cutting a range of sizes with ease. The 2,100W motor has a brake, soft start, overload protection and constant speed for whatever material you are cutting. Expanding worktop gives up to 635mm width and at 90° 79mm depth. The rip fence is fitted with the Bosch self-aligning Squarelock™ for precision every time and the integrated sliding table with mitre fence will handle work up to 350mm. There is on-board storage for cables, blades and other accessories, so you have everything to hand. Integrated handles on the machine table top allow for easy transport. Supplied with 24T tungsten tipped saw blade, mitre fence, push stick and dust adaptor.
|Blade Diameter||254 mmno value|
|Blade Tilt||-1° to 47°|
|Bore Size||30 mm|
|Dust Extraction Outlet||60 mm|
|Max Depth of Cut @ 45deg||56 mm|
|Max Depth of Cut @ 90deg||79 mm|
|Max Ripping Width||635 mm|
|Max Width of Cut with Fence||635 mm|
|Model||GTS 10 XC|
|Nett Weight||35 kg|
|Overall L x W x H||775 mm x 768 mm x 343 mm|
|Table Size||584 mm x 759 mm|
|Table Size With Extensions||759 mm x 885 mm|
18 August 2018
spedizione perfetta ma........Ottimi tempi di consegna ma è stato commesso un grave errore : mi hanno spedito il banco sega in Italia con la spina UK.Non posso sostituire la spina pena la perdita di garanzia e quindi ho ordinato un adattatore e per vedere la sega in funzione dovrò aspettare che arrivi. Sono molto deluso del servizio di AXMINSTER mi aspettavo più attenzione.
11 March 2018
Superb piece of kitI bought this saw from Axminster in Basingstoke where I saw it on a chance visit for something completely different. The idea was to replace a tired.old Jet site saw. It did that and more.
26 December 2017
Buy in person! tips to look for to get a good one and the rest can be tweaked.I went to a few stores to look for a good example. A high or warped sliding table is a deal breaker. A common complaint is a wobble left to right in the sliding mitre table. Easy fix on youtube, I took out the sliders and sprayed the edges with polyeurethane clear coat and it is snug and perfect. Hunt for one that is level or a half-mm high perhaps. Aligning blade to mitre slots is easy just loosen the front motor mounts and adjust and tighten. The fence is almost perfect and can be tweaked to perfection. Mine saw is darn near perfect now in every way. Dust extraction is kind of a mess as the shroud inside lets half the dust fall within the housing rather then out through the port. I doubt that other saws in this category are better in that way. The saw looks and feels like a quality precision tool. The plastic base doesnt feel cheap. It's quiet. The vacuum I use for dust extraction is louder than the saw. soft start is great. Get one, but be prepared to tweak it, and find a good unit to begin with.
8 December 2017
sliding tableif your buying this saw for the sliding table don't u basically have set it up each time and then 9/10 times you won't get an accurate cut.
27 August 2017
Nice machineI bought this saw to replace a worn out diy saw and I have to say that it is a very good machine and can be used straight from the box. However now that I am starting to make toys and segmented turning again a couple of faults have shown up namely the riving knife does not allow slot cutting as the knife in it's lowest position is still higher than the blade by a couple of mil and I had to file the top of the knife which has fixed this problem and the other fault is the position of the riving knife guard clamp, the tightening handle should be on the other side to prevent the fence hitting it when cutting narrow stock, but this is great machine which I am sure I will enjoy using and a three year warranty as well.